Crown Molding on Cabinets

Crown Molding on Cabinets

One method to offer your wall cupboards a completed, brightened touch is by setting up crown molding along the leading edge. Crown molding assists eliminate the dark appearance of open soffits on wall surface cabinets and also provides a fine woodworking look, even if you only have beginner carpenter abilities.

Just how Does This Job?
The crown molding is not nailed directly to the wall closets. The method that makes this task so easy is with the enhancement of wood nailing strips on top of the wall cabinets. These strips aid you precisely position the crown molding as well as supply a place to nail onto other than the closet face. Due to the fact that the strips are stepped back, the crown molding will cover them, making them unnoticeable.

Security Factors to consider
Since wall surface cupboards run parallel to lower base cupboards, the lure might be to use the kitchen counter on the base cupboards as a ladder. Resist that temptation. For many do-it-yourselfers, countertops are too expensive to make use of for this work. Not just that, countertops are slippery, and also you risk of harming them by standing on them. Utilize a ladder for this job.

With the determining tape, determine the size and also deepness of the wall surface cabinets. Both measurements are necessary because the crown molding will wrap around the closets. Then, complete the two figures. For example, for a basic 36-inch large wall surface cabinet with a depth of 12 inches, the complete number would be 60 inches. The total is included a front width of 36 inches, a left depth of 12 inches, as well as an ideal deepness of 12 inches.

Procedure the Crown Molding Lower Edge.
For the sleekest look, the bottom side of the crown molding will certainly be flush with the face of the closets. This indicates that the nailing strips require to be stepped back on all sides by the density of the reduced side of the crown molding. With the measuring tape, determine this density. For many popular crown molding accounts, this thickness is about 1/8-inch.

Cut the Nailing Strips.
Cut the nailing strips to the closet boundary size, minus the thickness of the crown molding’s reduced edge. So, if the crown molding’s reduced side thickness is 1/8-inch, you would certainly have:.

Position the Nailing Strips.

Lay the front nailing strip on the top of the cabinet as well as set it back by the thickness of the crown molding’s reduced edge. With this example, that would certainly be a 1/8-inch space. Facility the strip to ensure that there is a room of 1/8-inch on each side. Repeat for the two side strips, establishing each strip back by 1/8-inch. It can be helpful to establish these set-backs with the crown molding itself as opposed to depending on a measuring tape.

Safeguard the Nailing Strips.
Use the nail weapon to nail the strips to the top of the cabinet.

Action as well as Cut the Crown Molding Front Area.
Procedure as well as mark the front area of crown molding to the cupboard width. Set the miter attended a 45-degree angle cut. Location the crown molding to make sure that it is rests upside-down and also at a 45-degree angle versus the saw fence. Cut at one mark, then relocate the molding along to the next mark. Setting the saw to the opposite 45-degree angle cut and also make the second cut.

Hold the molding front section against the front nailing strip. Ensure that it is precisely placed. With the toenailing gun, drive a number of nails through the lower side of the crown molding and right into the toenailing strip. At this point, the crown molding might droop a little bit, but this will be dealt with when you include the side areas.

Action as well as Cut the Crown Molding Side Sections.
Both side areas of crown molding just need angle cuts on one side; the opposite side can be a straight 90-degree cut. For the left area of crown molding, make a 45-degree on one side to complement the front crown molding’s 45-degree left side. Repeat this for the right side.

Equally as you left a development gap between the side nailing strips and also the wall, do the very same for the side crown molding sections. See to it that you leave about a 1/8-inch gap as opposed to having the crown molding touch the wall.

Affix the Crown Molding Side Sections.
For this step, it aids to have an assistant raise the front section of crown molding to make sure that it goes to a 45-degree angle placement. Place the left section of crown molding against the left nailing strip. Ensure that both 45-degree angle flared sections of crown molding completely fulfill. With one hand strongly holding that tilted joint, nail the side crown molding area in position. Drive one brad via one board to the adjoining one to help them stay together. Repeat for the right side.

Repaint as well as Complete the Crown Molding.
Prior to painting, cover the closets with sheet plastic or masking film and also protect it with painter’s tape. Depending upon the dimension of the nail holes, you may desire to load them with wood putty or leave them unfilled. Interior paint can commonly appropriately load the little holes generated by electrical nail weapons. Layer with a minimum of 2 layers of paint. Let the paint remedy for at least four hours prior to eliminating the plastic. If you are working with unprimed crown molding, you have to first apply 2 coats of primer prior to paint.

Tips For Setting Up Crown Molding on Cabinets.
Precisely place the wood nailing strips along the top of the cupboards. If you place the strips too far forward or backward, a narrow but visible line will certainly mar the appearance.
Be sure to make use of an electric nail gun. Not just does this valuable device allow you shoot slim brad nails as well as stay clear of dividing your closets, however it can likewise reach into low soffit locations where it can be difficult to swing a hammer.
When buying the one-by-two lumber for the toenailing strips, stay clear of furring strips as they have harsh sides. Instead, choose spruce, pine, fir, or an additional softwood with great, straight edges.

The crown molding is not nailed straight to the wall surface cabinets. These strips aid you properly position the crown molding and also provide an area to nail onto other than the cabinet face. Lay the front nailing strip on the top of the cabinet as well as set it back by the thickness of the crown molding’s reduced side. Step and also mark the front section of crown molding to the cupboard size. For the left section of crown molding, make a 45-degree on one side to match the front crown molding’s 45-degree left side.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.